Smeg STA4645U Manuel d'instructions

INSTRUCTION MANUAL GGUUIIDDEE FFOORR UUSSIINNGG TTHHEE DDIISSHHWWAASSHHEERR AANNDD TTHHEE WWAASSHHIINNGG PPRROOGGRRAAMMSS

Rev 0.0 9USER INSTRUCTIONSEN 2.2.4 Interrupting a program To interrupt the current program simply open the door of the dishwasher; to restart the pr

10 Rev 0.0USER INSTRUCTIONSEN 2.2.7 Options PROGRAM DELAY The “Program delay” function delays the beginning of the washing program up to 9 ho

Rev 0.0 11USER INSTRUCTIONSEN 2.2.8 Switching off At the end of the program, the dishwasher emits a short beep and the indica-tor lights of the fo

12 Rev 0.0USER INSTRUCTIONSEN N.B.: the display indicates the water hardness adjustment and the program delay. A dot (.) after the number means t

Rev 0.0 13USER INSTRUCTIONSEN 3 ENERGY SAVING AND ENVIRONMENTAL RESPECT Always try to run the dishwasher fully loaded.Do not wash the dishes under

14 Rev 0.0USER INSTRUCTIONSEN 4 REMOVING THE DISHES At the end of the washing program, wait at least 20 minute before removing the dishes in ord

Rev 0.0 15USER INSTRUCTIONSEN 5 TROUBLESHOOTING The dishwasher can to signal a number of malfunctions by turning on various indicator lights, as des

16 Rev 0.0USER INSTRUCTIONSENIf an alarm situation occurs, the dishwasher interrupts the current program and signals the fault. Alarms E1, E3, E4,

Rev 0.0 1CONTENTSENContents1 INTRODUCTION ... 32 IMPORTANT SAFET

2 Rev 0.0EN

Rev 0.0 1CONTENTSENCONTENTS1 INTRODUCTION ... 3 2 DESCRIPTION AN

Rev 0.0 3INTRODUCTIONEN1 INTRODUCTION Thank you for choosing one of our products. To use this dishwasher correctly and safely, please read this manual

4 Rev 0.0INTRODUCTIONEN Symbols used in this manual (see tab. 1-01) DANGER. This symbol highlights information and warnings which, if not observed,

Rev 0.0 5WARNINGSEN2 IMPORTANT SAFETY INSTRUCTION (Save this instructions) THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLI-ANCE: IT MUST ALWAY

6 Rev 0.0WARNINGSENBEFORE PROCEEDING WITH INSTALLATION, DISCONNECT THE MAINS POWER SUPPLY FROM THE WORK AREA.DO NOT USE EXTENSION CORDS, ADAPTORS OR

Rev 0.0 7WARNINGSENONLY USE RINSE-AID SPECIALLY FORMULATED FOR DOMESTIC DISHWASHERS. DO NOT INHALE OR SWALLOW DETERGENT AS THIS MAY CAUSE BURNS

8 Rev 0.0WARNINGSEN DO NOT INTRODUCE ITEMS IN HEAT-SENSITIVE PLASTI¬C, SUCH AS DISPOSABLE CUTLERY OR PLATES, AS THESE MAY BECOME DEFORMED. DO NOT

Rev 0.0 9WARNINGSEN KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST BE PLACED IN THE CUTLERY BASKET BLADE-DOWN, OR LAID HORIZONTAL IN THE UPPER R

10 Rev 0.0WARNINGSENBEFORE CLEANING OR SERVICING THE APPLIANCE, REMOVE THE PLUG OR TURN OFF THE MULTI-POLE SWITCH. REMOVE THE WASHING COMPARTMENT DOO

Rev 0.0 11INSTALLATION INSTRUCTIONSEN3 INSTALLATION AND HOOK-UPTo install and hook up this appliance, consult the attached installation manual.Bear i

12 Rev 0.0INSTALLATION INSTRUCTIONSEN CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE AP-PLIANC

2 Rev 0.0EN

Rev 0.0 13INSTALLATION INSTRUCTIONSENDO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CON-NECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEAT-ING OR B

14 Rev 0.0USER INSTRUCTIONSEN4 OPERATING INSTRUCTIONS BEFORE STARTING TO USE THE APPLIANCE, MAKE SURE YOU HAVE READ AND UNDERSTOOD ALL THE WARNINGS

Rev 0.0 15USER INSTRUCTIONSEN 4.1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whi

16 Rev 0.0USER INSTRUCTIONSENA When using the dishwasher for the fi rst time, in addition to the salt it is also necessary to add one liter of water

Rev 0.0 17USER INSTRUCTIONSEN 4.2 Using the rinse-aid and detergent dispensersThe detergent and rinse aid dispensers are situated on the inner part

18 Rev 0.0USER INSTRUCTIONSEN4.2.1 Adding the rinse-aid The rinse aid helps the dishes dry faster and prevents the formation of scale de-posits and

Rev 0.0 19USER INSTRUCTIONSEN To adjust the rinse aid setting, rotate the dispenser cover (ref. A fi g. 4-04) through a quarter turn in an anticlockw

20 Rev 0.0USER INSTRUCTIONSENAB When a program with hot prewash is selected (see program table in the “De-scription of Controls” manual), extra dete

Rev 0.0 21USER INSTRUCTIONSEN When using detergent tabs, place them in the cutlery basket. The dispenser has been designed for powder or liquid det

22 Rev 0.0USER INSTRUCTIONSENMAKE SURE that the items being washed are dishwasher-safe. Items which are not dishwasher-safe: Wooden dishes, pots or

Rev 0.0 3INTRODUCTIONEN 1 INTRODUCTION Thank you for choosing one of our products. To use this dishwasher correctly and safely, please read this manu

Rev 0.0 23USER INSTRUCTIONSEN 4.4 Using the racks The dishwasher has a capacity of 10 place-settings, including serving dishes. Examples of loadin

24 Rev 0.0USER INSTRUCTIONSENFig. 4-09 4.4.1 Lower rackThe lower rack receives the full force of the lower spray arm, and should there-fore be used

Rev 0.0 25USER INSTRUCTIONSENLoading the lower rack (see fi g. 4-10) Carefully load fl at plates, soup plates, dessert and serving dishes, position-ing

26 Rev 0.0USER INSTRUCTIONSEN 4.4.2 Cutlery basket (see fi g. 4-11) The cutlery basket can be removed to simplify unloading. Arrange the cutlery in

Rev 0.0 27USER INSTRUCTIONSEN 4.4.3 Upper rack (vedi fi g. 4-12, 4-13)It is recommended to load the upper rack with small- or medium-sized items such a

28 Rev 0.0USER INSTRUCTIONSEN Loading the upper rack (vedi fi g. 4-14) Load plates facing forward; cups, bowls etc. must always be facing downwar-ds.

Rev 0.0 29USER INSTRUCTIONSEN Adjusting the upper rackThe upper rack can be adjusted in two positions, according to the user’s needs and according to

30 Rev 0.0USER INSTRUCTIONSEN5 CLEANING AND USER-MAINTENANCE BEFORE CARRYING OUT ANY WORK, ALWAYS DISCONNECT THE APPLIANCE FROM THE ELECTRICAL P

Rev 0.0 31USER INSTRUCTIONSEN 5.2 Cleaning the water intake fi lter (only some models) The water intake fi lter (ref. B fi g. 5-01) loc

32 Rev 0.0USER INSTRUCTIONSENABAB •••••••Fig. 5-02Fig. 5-03Fig. 5-04

4 Rev 0.0INTRODUCTIONEN Symbols used in this manual (see tab. 1-01) DANGER. This symbol highlights information and warnings which, if not observed,

Rev 0.0 33USER INSTRUCTIONSENFig. 5-05Fig. 5-06 5.4 Cleaning the fi lter unit Periodically inspect the fi lter unit (ref. A fi g. 5-05) and, if necess

34 Rev 0.0USER INSTRUCTIONSEN 5.5 General warnings and recommendations for correct maintenance Clean the fi lters under running water (at room te

Rev 0.0 35USER INSTRUCTIONSEN Prolonged disuse Run the soak program twice in succession. Unplug the power cord from the socket. Leave the door slight

36 Rev 0.0USER INSTRUCTIONSEN If the dishes fail to dry or remain dull, check that:there is rinse aid inside the special container; the rinse-aid

Rev 0.0 37USER INSTRUCTIONSEN6 TECHNICAL DATA (SEE TAB. 6-01) Width44.7 cm ÷ 44.9 cm (17 - 19/32” ÷ 17 - 43/64”)Depth measured fl ush with the outer ed

Rev 0.0 1CONTENTSENContents1 INTRODUCTION ... 32 SAFETY INFORMATI

2 Rev 0.0EN

Rev 0.0 3INTRODUCTIONEN 1 INTRODUCTIONThank you for choosing one of our products. To install this dish-washer correctly and safely, please read this m

4 Rev 0.0INTRODUCTIONENSymbols used in this manual (see tab. 1-01) DANGER. This symbol highlights information and warnings which, if not observed,

Rev 0.0 5WARNINGSEN 2 SAFETY INFORMATION THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE AND MUST THEREFORE BE KEPT INTACT TOGETHER WITH THE MA

Rev 0.0 5USER INSTRUCTIONSEN 2 DESCRIPTION AND USE OF THE CONTROLS 2.1 Upper panel All the dishwasher controls are grouped on the upper panel (see fi

6 Rev 0.0WARNINGSENTWO PEOPLE WEARING SAFETY GLOVES ARE REQUIRED TO LIFT THE DISHWASHER. DO NOT LEAVING DISCARDED PACKAGING MATERIALS UNSU-PER

Rev 0.0 7WARNINGSEN DO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CON-NECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEAT-ING OR BURNING, WITH CO

8 Rev 0.0INSTALLATION INSTRUCTIONSEN3 INSTALLATION MATERIAL To install the dishwasher correctly, the following materials are required: Phillips screw

Rev 0.0 9INSTALLATION INSTRUCTIONSEN3.1 Kit supplied with dishwasher (models sta_4645/sta_8743)The kit supplied with the dishwash

10 Rev 0.0INSTALLATION INSTRUCTIONSEN3.2 Kit supplied with dishwasher (models pla_8743)The kit supplied with the dishwasher comprises:adhesive steam

Rev 0.0 11INSTALLATION INSTRUCTIONSEN4 DIMENSIONS OF DISHWASHER (See fi g. 4-01) Model A (height) B (width) C (depth)STA874386 cm ÷ 91 cm33-55/64” ÷ 3

12 Rev 0.0INSTALLATION INSTRUCTIONSEN5 INSTALLATION AND HOOK-UP DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON THE SHARP EDGES OF THE

Rev 0.0 13INSTALLATION INSTRUCTIONSENIf the appliance is not in a niche and can therefore be accessed on one side, cover the door hinge area for safet

14 Rev 0.0INSTALLATION INSTRUCTIONSEN 5.1.2 Levelling the applianceLevel the appliance using the relative adjustable feet (e.g.: ref. A fi g. 5-02)

Rev 0.0 15INSTALLATION INSTRUCTIONSENFig. 5-03A5.2 Connections Install the dishwasher so as to allow ease of access to the electrical and hy-draulic

6 Rev 0.0USER INSTRUCTIONSENFig. 2-02 2.2 Setting the washing program and switching on and off The dishwasher is equipped with a control panel (see

16 Rev 0.0INSTALLATION INSTRUCTIONSENA through hole with a diameter of at least 8 cm (5/32”) is required to pass the hoses and power cord (ref. A fi g

Rev 0.0 17INSTALLATION INSTRUCTIONSEN 5.2.1.1 Connecting to the water tap Connect the inlet hose to a threaded ¾” gas cold water tap, fi tting the s

18 Rev 0.0INSTALLATION INSTRUCTIONSENDo not cut the inlet hose (see fi g. 5-07).If the hose is cut, the dishwasher will not work, water will leak and

Rev 0.0 19INSTALLATION INSTRUCTIONSEN5 .2.1.2 Connecting the drain hose Connecting to a drainInsert the relative hose into a drain with a minimum

20 Rev 0.0INSTALLATION INSTRUCTIONSENConnecting to a “T” union of the drain circuit MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND

Rev 0.0 21INSTALLATION INSTRUCTIONSENConnecting to a waste disposal unit with an air gap MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE

22 Rev 0.0INSTALLATION INSTRUCTIONSENConnecting to the air gap (no waste disposal unit) MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE

Rev 0.0 23INSTALLATION INSTRUCTIONSENConnecting to a waste disposal unit (no air gap) MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AN

24 Rev 0.0INSTALLATION INSTRUCTIONSEN5 .2.2 Electrical connections and warnings CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE

Rev 0.0 25INSTALLATION INSTRUCTIONSENPLUG IS NOT SUITABLE FOR THE SOCKET, CALL IN A QUALIFIED ELECTRICIAN TO FIT A SUITABLE PLUG.The plug at the end o

Rev 0.0 7USER INSTRUCTIONSENPROGRAM NUMBER AND SYMBOLDISHES AND CUTLERYPROGRAM SEQUENCETIME CONSUMPTIONMINUTES (2)WATER(1)ENERGYKWh (2)1RINSEPans and

26 Rev 0.0INSTALLATION INSTRUCTIONSENPush the dishwasher into position, taking care not to twist or crush the power cord or hoses (see fi g. 5-18). TW

Rev 0.0 27INSTALLATION INSTRUCTIONSEN 5.3.2 Procedure for mounting the door panel (models sta_4645/sta_8743)Mount the door panel.Place the template o

28 Rev 0.0INSTALLATION INSTRUCTIONSENDrill holes for the panel handle using a drill with a suitable bit. Use the screw-driver to secure the door hand

Rev 0.0 29INSTALLATION INSTRUCTIONSEN Secure the door to the panel with the supplied screws. The panel must have a minimum thickness of 20 mm (25/32”)

30 Rev 0.0INSTALLATION INSTRUCTIONSENFig. 5-25

Rev 0.0 31INSTALLATION INSTRUCTIONSEN5.3.3 Procedure for mounting the door panel (models pla_8743)Mount the door panel.Place the temp

32 Rev 0.0INSTALLATION INSTRUCTIONSENIf a gap is created between the control panel and the door panel (ref. A fi g. 5-28), use the supplied strips (re

Rev 0.0 33INSTALLATION INSTRUCTIONSENAttach the door panel: fi t the hooks into their slots on the dishwasher and allow the panel to slide upwards and

34 Rev 0.0INSTALLATION INSTRUCTIONSENMake sure the dishwasher door, complete with panel, opens comfortably and that the base plate (ref. A fi g. 5-32)

Rev 0.0 35INSTALLATION INSTRUCTIONSEN5.3.4 Completion of installation (all models)Finish the cut with a fi le (see fi g. 5-34) in order to remove any b

8 Rev 0.0USER INSTRUCTIONSENOnly run the soak program with half loads.After using the above table to choose the most suitable washing cycle, pro-gram

36 Rev 0.0INSTALLATION INSTRUCTIONSENBefore securing the dishwasher to the adjacent units, attach the gaskets to the sides.Remove the adhesive band o

Rev 0.0 37INSTALLATION INSTRUCTIONSENFig. 5-38AFig. 5-39 shows the state of the dishwasher after the above operations are performed.Fig. 5-39

38 Rev 0.0INSTALLATION INSTRUCTIONSENTighten the supplied screws with a screwdriver; this operation defi nitively fi xes the dishwasher to the adjacent

19 570 0074 00SXDXAlign with the top edge of the door panel.Aligner au bord supérieur du panneau de la porte.Alinear respecto del borde superior del p