Smeg KSEV90X Manuel d'utilisateur télécharger pdf (Page 8)

Instruction on mounting and use

Consult the designs in the front pages referenced in the text by

alphabet letters. Closely follow the instructions set out in

this manual. All responsibility, for any eventual

inconveniences, damages or fires caused by not complying

with the instructions in this manual, is declined.

Use

The hood is designed to be utilized either for suction version at

external evacuation or filtering version at internal recirculation.

Ducting version

The hood is equipped with a top air outlet B for discharge of

fumes to the outside (exhaust pipe and pipe fixing clamps not

provided). Attention!

If the hood is supplied with carbon filter, then it must be

removed.

Filter version

Should it not be possible to discharge cooking fumes and

vapour to the outside, the hood can be used in the filter

version, fitting an activated carbon filter and the deflector F on

the support (bracket) G, fumes and vapours are recycled

through the top grille H by means of an exhaust pipe connected

to the top air outlet B and the connection ring mounted on the

deflector F (exhaust pipe and pipe fixing clamps not provided).

Attention!

If the hood is not supplied with carbon filter, then it must

be ordered and mounted.

The models with no suction motor only operate in ducting

mode, and must be connected to an external suction device

(not supplied).

Installation

The minimum distance between the supporting surface for the

cooking vessels on the hob and the lowest part of the range

hood must be not less than 60cm from electric cookers and

70cm from gas or mixed cookers.If the instructions for

installation for the gas hob specify a greater distance, this must

be adhered to.

Electrical connection

The electrical tension must correspond to the tension noted on

the label placed inside the cooker hood. Connect the electrical

plug, where provided, to the an easily accessible outlet in

conformity with local standards in force. Where an electrical

plug is not provided (for direct connection to electrical network)

place a standards approved bipolar switch with an aperture

distance of not less than 3mm (accessible) from the contacts.

Attention: substituting the supply cable must be carried out by

the authorised technical assistance service.

Mounting

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take the

weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

Model with button panel

O1 2 3

b. c. d. e. f.

a. operating gauge.

b. on/off light switch

c. off aspiration switch

d. minimum power selection aspiration switch

e. medium power selection aspiration switch

f. maximum power selection aspiration switch

Functioning - 5-key electronic model

123OOI

1234 567 8 9

1. Motor OFF button

2. ON button and motor speed selection button 1 - 2 - 3 - 1

- 2 - . . . .

3. Speed 1 LED

4. Speed 2 LED and metal grease filter saturation LED (in

this latter case, the LED will flash - See instructions on

grease filter cleaning).

Once the grease filters have been cleaned, press button

1 for about 3 seconds until you hear the acoustic signal

(beep): the LED 4 will now stop flashing.

5. Speed 3 LED and active carbon filter saturation LED (in

this latter case, the LED will flash - See instructions on

active carbon filter replacement).

Once you have replaced the charcoal filter, press button

1 for about 3 seconds until you hear the acoustic signal

(beep). LED 5 will now stop flashing.

Warning!

The active carbon filter saturation LED is not activated.

In order to activate the active carbon filter saturation

indicator, press buttons 2 and 7 simultaneously for 3

seconds. Initially, only LED 4 will flash, then after the 3

seconds have passed, LED 5 will also start flashing,

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Smeg KSEV90X Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Ventilateurs Smeg KSEV90X