Smeg P23LINP Guide de dépannage télécharger pdf (Page 2)

• This appliance is a high efficiency, flueless catalytic flame effect gas fire. It provides radiant and convected warmth both effi-

ciently and safely utilising the latest type catalytic converter and burner technology.

• The appliance does not require a flue system of any type as the catalytic converter cleans the flue products to provide a com-

plete combustion system, which is intrinsically safe. It is designed to operate on Natural Gas and is factory set for operation on

the gas type, and at the pressure stated on the appliance data plate.

• The appliance incorporates a combustion monitoring system (Oxygen Depletion System). It must not be adjusted or put out

of operation. If replaced then manufacturer’s original parts must be used.

• This appliance must be installed by a competent person to ensure that the size of the room in which the appliance is to be

installed is sufficient and the ventilation provision for that room is sufficient for the appliance. Details of how to determine the

suitable room size is given in section 3.1 of these instructions and details of how to determine suitable ventilation are given in

section 4.1.

• In the event of gas leakage from the appliance, the gas supply must be turned off at the nearest isolating valve.

• The appliance must be installed in accordance with the following:

• Failure to comply with the above could lead to prosecution and deem the manufac-

turer’s warranty invalid.

• This appliance must be installed in accordance with the rules in force and used only

in a sufficiently ventilated space. The appliance is designed to fit various types of situa-

tions as described in sections 3.0 and 4.0. The appliance must be installed in a correct-

ly sized room (see section 3.1), and the correct purpose provided ventilation must be

provided (see section 4.1).

• On no account should the appliance inlet or outlet openings be blocked or obstruct-

ed in any way (see figure 1). Do not place objects on top of the appliance. Do make

sure the appliance is installed on a flat wall.

• It should be noted that heaters create warm air currents. These currents move heat

to wall surfaces next to the heater. Installing the heater next to vinyl or cloth wall cov-

erings or operating the heater where impurities in the air (such as tobacco smoke, can-

dle smoke etc.) exist, may cause the walls to become discoloured.

• This appliance is intended as a secondary source of heat only and should not be used

in a room without some form of background heating present. If the appliance is used in a room as the sole source of heat, then

condensation may occur on colder surfaces within the room.

• On first light up of a new appliance, burning off of high temperature paint and lubricants may occur for the first few hours of

operation. During this period some smoke may be emitted from the outlet grille, this should be no cause for concern.

Accordingly, the room should be well ventilated with all windows and doors open during this period. During this period the

appliance may cause smoke alarms to sound. If this happens, reset the alarms, but do not remove the batteries.

• WARNING: Due to the nature of this product the area around the top of the appliance (i.e. the grille) gets very hot. Care

should be taken when operating the appliance. The manufacturer of this appliance considers all surfaces as working surfaces

with the exception of the control knob. The guard (glass front) is to prevent risk of fire or injury from burns and no part of

it should be permanently removed. It Does Not Give Full Protection For Young Children Or The Infirm. Where

young children, pets, the elderly or infirm are concerned, a suitable fireguard should be used.

• Consult ALL instructions before installation and use of this appliance. This appliance is free from any asbestos material.

Section Contents Page No.

1.0 Important Notes 2

2.0 Appliance Data 3

3.0 Installation Requirements 3

.1 Room Sizing 3

4.0 Site Requirements 4

4.1 Ventilation 4

5.0 Unpacking the Appliance 5

5.1 Component Checklist 5

.0 Gas Supply Routes 5

7.0 Fixing the Appliance 6

7.1 Checking the Burner & Spark Gap 6

Section Contents Page No.

8.0 Testing and Commissioning 6

8.1 Operating the Appliance 7

8.2 Setting pressure 7

.3 Fitting the Decorative Frame 8

9.0 Briefing the customer 8

10.0 Servicing 8

10.1 Servicing the Burner Unit 9

10.2 Pilot Assembly 9

0.3 Catalysts 10

10.4 Testing for Firebox Leakage 10

11.0 Troubleshooting Guide 11

1.0 IMPORTANT NOTES

I N S T A L L A T I O N I N S T R U C T I O N S

• Manufacturers' Instructions.

• Local Codes and/or Regulations.

Note : L30FAB shown from rear as example,

however the air inlet and outlet openings are in

the same relative positions on all models.

Figure 1

Outlet openings :

DO NOT BLOCK

Inlet openings :

DO NOT BLOCK

GB IE

GB-IE-2

Smeg EU-wide instal instruc-v7-English.qxp:Smeg EU-wide installation instructions DRAFT A-12-12-07.qxd 17/7/08 12:06 Page 2

1 2 3 4 5 6 7 ... 14 15

Commentaires sur ces manuels

Pas de commentaire

Smeg P23LINP Guide de dépannage Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Foyers Smeg P23LINP