Smeg P23LINP Guide de dépannage télécharger pdf (Page 6)

If the appliance is to be mounted on a dry lined wall or

a timber framed construction wall then efforts should

be made to fix in at least two positions vertically, into

ne of the wooden studs, or supporting wooden mem-

bers of the wall using two of the fixing screws provid-

ed. If this is not achievable then

the wall should be strength-

ened using appropriate building materials.

f there is no alternative than to rely on some plasterboard fixings then

special cavity screw fixings or hollow wall anchors will be required which

are not supplied with this product. These should be constructed from

metal and not plastic and of the design indicated in figure 3. For further

guidance for wall fixing in timber framed buildings refer to any relevant

local codes of practice.

Flat Wall Fixing - All Models

To assist with fixing the appliance, a template is provided. The L23 model

template is shown for the purposes of example in figure 4.

Mark the positions shown as “Fixing points” on the wall.

If a concealed gas connection is to be made ensure the gas supply pipe is

in its final position and can enter the appliance in the correct position

when the appliance is hung on the wall.

Drill the wall as appropriate for the type of wall as previously described

in this section, and insert the chosen type of wall fixings. Insert the wall

fixing screws into the top wall plugs, taking care to leave the screws pro-

truding approximately 5mm from the wall. Now hang the appliance onto

these screws through the two keyhole shaped holes in the upper brack-

ets on the back panel of the appliance.

Insert the lower fixing screws into the lower wall plugs through the cor-

responding fixing holes in the lower part of the back panel. Do not tight-

en fully.

Before tightening the wall mounting screws fully, at this stage it is recom-

mended to check the horizontal alignment of the appliance with a spirit

level, as small adjustments can still be made if necessary. When this has been checked, tighten all four fixing screws fully.

To access the upper fixing screws insert a screwdriver through the round access holes in the front face of the outlet grille (as

shown in figure 5). These access holes are located in the same position on all models.

There are no imitation fuel bed components to install. The appliance features a ribbon

burner which is designed to produce a continuous band of flame over its length.

The burner should be visually inspected to ensure it is free from any foreign matter.

If it is necessary to clean or dust off the burner then the glass door should be removed

by removal of the four retaining screws. Re-fit the glass door after cleaning or inspection,

ensuring a good seal. The gap between the spark electrode and the pilot should be 3 -

5mm to produce a good spark (see figure 6).

There should be no need to adjust this. If under any circumstances the piezo electric

spark fails, the pilot cannot be lit manually.

The appliance is supplied with a selection of inlet adaptors for use in the various countries of destination. Select an appropriate

adaptor and connect to the flared inlet connection of the appliance. Ensure the inlet adaptor/connection is fully tightened. Turn

on and test the gas supply up to the fire for any leaks, in accordance with local Codes and/or Regulations.

2008 Smeg S.p.A.

Figure 4

7.0 FIXING THE APPLIANCE (

CONTINUED)

GB IE

igure 3

Plasterboard alone is not consid-

ered to be a structural material.

It is not recommended to rely on

plasterboard fixings alone to sup-

port the weight of the appliance.

ARNING

Figure 5

7.1 CHECKING THE BURNER AND SPARK GAP

Figure 6

Spark gap

8.0 TESTING AND COMMISSIONING

GB-IE-6

Smeg EU-wide instal instruc-v7-English.qxp:Smeg EU-wide installation instructions DRAFT A-12-12-07.qxd 17/7/08 12:07 Page 6

1 2 3 4 5 6 7 8 9 10 11 ... 14 15

Commentaires sur ces manuels

Pas de commentaire

Smeg P23LINP Guide de dépannage Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Foyers Smeg P23LINP