Smeg Built-in Electric Hob HBE64CAS Manuel d'utilisateur télécharger pdf (Page 6)

INSTALLATION

Installation and maintenance must only be

carried out by a qualified installer.

Incorrect installation could cause damage to

persons, animals and property for which the

manufacturer cannot be held responsible.

4) INSTALLING THE HOT PLATE

Check that the appliance is in a good condition

after having removed the outer packaging and

internal wrappings from around the various loose

parts. In case of doubt, do not use the appliance

and contact qualified personnel.

Never leave the packaging materials

(cardboard, bags, polystyrene foam, nails,

etc.) within children's reach since they could

become potential sources of danger.

The measurements of the opening made in the top

of the modular cabinet and into which the hot plate

will be installed are indicated in either fig. 4, comply

with the measurements given for the hole into which

the appliance will be recessed (see fig. 5).

If a wood is installed above the hob, please look at

the hood manufacturer instructions regarding the

minimum distance between hood and hob (fig. 5).

5) FIXING THE HOT PLATE

The hob has a special seal which prevents liquids

from infiltrating into the cabinet. Strictly comply

with the following instructions in order to correctly

apply this seal:

- Detach the seals from their backing, checking

that the transparent protection still adheres to the

seal itself.

- Overturn the hob and correctly position seal “E”

(fig. 6) under the edge of the hob itself, so that

the outer part of the seal itself perfectly matches

the outer perimetral edge of the hob. The ends of

the strips must fit together without overlapping.

- Evenly and securely fix the seal to the hob,

pressing it in place with the fingers.

- Remove the strip of protective paper from the

seal “F” it the hooks into their relative housings

“K” in the unit and set the hob into the hole in the

cabinet. Lock it in place with the relative fixing

screws “F” (see fig. 7).

WARNINGS:

Be aware that the glue that join the

laminated plastic to the furniture, has to

resist to temperature not below 150° C, to

avoid the unstuck of the panelling.

The installer should bear in mind that the

mixed appliance is the Y type. The rear wall,

adjacent and surrounding surfaces must

therefore be able to withstand an

overtemperature of 65 K.

FIG. 4 FIG. 5 FIG. 6

FIG. 7

INSTALLATION

FIG. 8

6) ELECTRICAL CONNECTIONS

Electrical connection must be carried out in

compliance with the specifications and

provisions in force.

Before proceeding with the connections, check that:

- The voltage rating of the appliance and the

current sockets suits the maximum power draw

of the appliance (see data label affixed to the

lower part of the appliance itself).

- The system is equipped with an efficient earth

connection in compliance with the pertinent

provisions in force. The manufacturer declines all

responsibility for failure to comply with these

provisions.

- If the appliance has no power cable, connect a

cable of adeguate section to the terminal strip

(consult the table on next page) complying with

the wiring diagram of fig. 8. This diagram is also

affixed to the hot plate.

When connection to the electricity main is

made by using a socket (gas version only):

- Fit a standard plug to power cable (if supplyied).

This plug should be able to bear the load

indicated on the data label. Connect the wires

according to the diagram in fig. 8, remembering

to comply with the following instructions:

letter L (live) = brown wire;

letter N (neutral) = blue wire;

earth symbol = yellow-green wire.

- The powering cable must be positioned so that it

is never able to reach an overtemperature of 75

K in any part.

- Never use reductions, adapters or shunts for the

connection since these could cause false

contacts and dangerous overheating.

When the appliance is connected straight to

the electricity main:

- Install an omnipolar cutout between the

appliance itself and the main. This circuit-breaker

should be sized according to the rating of the

appliance and the opening between its contacts

should be at least 3 mm.

- Remember that the earth wire must not be cutout

by the switch.

- Alternatively, the electrical connection may also

be protected by a high sensitivity differential

switch.

Installers are strongly advised to connect the

yellow- green earthing wire to an efficient earthing

system.

The manufacturer cannot be responsible for the

missing earthing of the appliance.

WARNINGS:

All our appliances are designed and

manufactured in compliance with European

standards EN 60 335-1 and EN 60 335-2-6

plus the relative amendments.

The appliance complies with the provisions

of the following EEC Directives:

- CEE 89/336 + 92/31 + 93/68 regarding to

electromagnetic compatibility.

- CEE 73/23 + 93/68 regarding electrical

safety.

1 2 3 4 5 6

Commentaires sur ces manuels

Pas de commentaire

Smeg Built-in Electric Hob HBE64CAS Manuel d'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Plaques chauffantes Smeg Built-in Electric Hob HBE64CAS