Smeg STFABUWH Manuel d'instructions télécharger pdf (Page 13)

USER INSTRUCTIONS

f fo gnihct iwS 8.2.2

eh t dna peeb t r ohs a s t ime r ehsawhs i d eh t ,ma r go r p eh t f o dne eh t t A indi-

cator lights of the fourth and ﬁ fth program (ref. pr. 4, pr. 5 ﬁ g. 2-04) ﬂ ash.

Turn off the appliance by opening the door and pressing the on/off button (ref.

1 ﬁ g. 2-02).

FIG. 2-04

If it is necessary to open the door during the washing cycle, the

program will be interrupted, the relative indicator light will continue to

ﬂ ash and a beep will indicate that the cycle has not terminated. Wait

for about 1 minute before closing the door and continuing with the

program. When the door closes, the program will start from where it

was interrupted. This operation should be performed only if neces-

sary as it could cause irregular program performance.

SEHS I D EHT G N I V OME R 4

˜˜˜

t sae l t a t i aw ,m a r go r p gn i hsaw eh t f o dne eh t t A 20 minute before

removing the dishes in order to allow them to cool. To prevent any

water droplets on the upper rack from falling onto the dishes in the

lower rack, empty the lower rack ﬁ rst and then the upper one.

2.2.9

symbols programs according to the models

2.3 Additional functions

2.3.1 Adjusting the water softener (on some models only)

N.B.: a different washing program from soak must be used to make

the following adjustment.

Press and hold down the program delay button (ref. 12 ﬁ g. 2-05) until the

preset value appears followed by a dot (normally 3.). Release the button and

then press it again and again until the required value is displayed, as indicated

in the table (see tab. 2-03).

The 6 possible adjustment levels will appear in this sequence:

3., 4., 5., 0., 1., 2..

When the required value appears on the display, release the button; after 5

seconds the appliance automatically reverts to the program delay and the

adjustment is set to the chosen value.

81012 9

11 67

QuickTime

Auto

Sanitized

Auto

cancella programma

spegnimento

Auto

min

USER INSTRUCTIONS

N.B.: the display indicates the water hardness adjustment and the

program delay. A dot (.) after the number means that the water har-

dness adjustment is being displayed. If no dot (.) appears, the pro-

gram delay is being displayed.

FIG. 2-05

Water hardness table (see tab. 2-03)

WATER HARDNESS

SETTING

German degrees (°D) French degrees (°F)

American degrees

grains/galls

0 - 4 0 - 7 0 - 4.5 0.

155 - 8 - 25 -4.6 14.5 1.

2316 - 26 - 40 14.6 - 23.5 2.

3124 - 41 - 60 - 3523.6 3.

4732 - 61 - 80 4.

5848 - 81 - 100

35.1 - 46.5

46.6 - 58.5 5.

Tab. 2-03

Contact your local water board for information on the hardness of your water

supply.

USER INSTRUCTIONS

L A TNEMNOR I VNE DNA GN I V A S YGRENE 3

RESPECT

• Always try to run the dishwasher fully loaded.

• Do not wash the dishes under a running tap.

• Use the most suitable washing program for each type of load.

• Do not pre-rinse.

• If available, connect the dishwasher to a hot water system with a tempera-

ture of up to 60°C (140°F).

• When possible, skip the drying cycle by opening the door after washing:

the air and the residue heat will dry the dishes to perfection.

3.1 Reducing the consumption of detergent

and respecting the environment

- i vne eh t o t l u fmr ah e r a s t neg r e t ed r ehsawhs i d n i den i a t noc se t ahpsohp ehT

ronment. To avoid using excessive amounts of detergent and to save on elec-

tricity:

• Separate the more delicate items from those that are more resistant to ag-

gressive detergents and high temperatures;

• Do not pour . sehs i d eht otno y l tcer id tnegreted eht

81012 9

11 67

QuickTime

Auto

Sanitized

Auto

cancella programma

spegnimento

Auto

min

2.3 ADJUSTING THE WATER SOFTENING SYSTEM

The dishwasher is equipped with a device which allows the softener setting to

be varied to suit the hardness of the mains water. The hardness is set using the

PROGRAM SELECTION BUTTON (3).

To access the setting function, hold the button down for more than 15 secon-

ds. The WATER HARDNESS ADJUSTMENT INDICATOR LIGHT (4) flashes,

while the SELECTED PROGRAM INDICATOR LIGHTS (2) show the current

setting. Each pressure on the button changes the setting following the se-

quence in the table below:

Water hardness table (see tab. 2-03)

WATER HARDNESS

SETTING

German

degrees (°dH)

French

Degrees (°dF)

0 - 6 0 - 11

All lights off

(no salt)

H0 -

7 - 10 12 - 18 One light on

H1 -

11 - 15 19 - 27 Two lights on

H2 -

16 - 21 28 - 37 Three lights on

H3 -

22 - 28 38 - 50 Four lights on

H4 -

29 - 35 51 - 62 Five lights on

H5 -

36 - 50 63 - 90 Two lights on

H6 -

Contact your local water board for information on the hardness of your water

supply.

After adjustment or display of the current setting, simply do not touch the but-

ton for a few seconds; the dishwasher will automatically return to standard

mode, quitting the adjustment mode.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

Smeg STFABUWH Manuel d'instructions Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Smeg STFABUWH