Smeg 50's Retro style Guide de dépannage télécharger pdf (Page 9)

Please note that the Linear and Classic models are

supplied with a tinted glass facia assembly, which dif-

fer in appearance when viewed from the front, simi-

larly the Fab model is supplied with a metal facia,

however the method of attachment to the appliance,

for all frame designs, is the same.

All models : Remove the facia panel from any protec-

tive packaging. Ensure all/any protective film is removed

as the facia may be damaged if the fire is lit with the facia

in position whilst still covered in film.

The facia panel is supported by four M6 screws which

protrude from the front

of the outer casing as

shown in figure 11.

Ensure each screw is

unscrewed approxi-

mately one turn from

the fully screwed in

position in order to

create a 2mm gap as shown in figure 12.

Simply hang the facia panel onto the outer casing ensur-

ing that the corresponding keyhole shaped holes engage

the screwheads fully.

All instructions must be handed to the user for safekeeping. Show the customer how to light and control the fire.After commis-

sioning the appliance, the customer should be instructed on the safe use of the appliance and the need for regular servicing.

Frequency of service depends on usage, but MUST be carried out at least once annually.

Advise that cleaning of the fire maybe achieved when the fire is cold using a damp cloth and mild detergent on most surfaces.

Advise that on first light up of a new appliance, initial curing of high temperature paint and burning off of lubricants may occur for

the first few hours of operation. During this period some smoke may be emitted from the outlet grille, this should be no cause

for concern. Accordingly, the room should be well ventilated with all windows and doors open during this period. During this

period the appliance may cause smoke alarms to sound. If this happens, reset the alarms, but do not remove the batteries.

Recommend that a guard be used for the protection of the young, pets, the elderly and the infirm.

Isolate the fire from the gas supply. Ensure that the fire is fully cold before attempting service.

A suggested procedure for servicing is detailed below.

2mm

8.3 FITTING THE DECORATIVE FRAME ASSEMBLY

9.0 BRIEFING THE CUSTOMER

10.0 SERVICING

Figure 11

Figure 12

1. Lay out the dustsheet and tools.

2. Remove the decorative frame/glass facia assembly. Removal is reverse of section 8.3.

3. Remove the glass door assembly (4 screws) and clean carefully.

4. Inspect the burner and the catalyst and clean if necessary with a soft brush.

5. Disconnect the gas supply.

6. Detach the burner front cover plate by removal of the four retaining screws. Undo the four screws retaining the

burner support brackets to the base and rear of the firebox. Remove the control knob and spindle assembly from the

valve by removal of the spindle retaining clip.

7. Remove the burner unit, strip off the burner pipes and clean thoroughly.

8. Clean the in-line restrictor, pilot assembly and the burner tube. Do not attempt to remove the pilot injector as this

can cause damage.

9. Re-assemble components.

10.Turn on the gas supply and leak test. Check pilot and burner for good ignition.

11. Refit the glass door assembly, ensuring correct orientation and a good seal.

12. Refit the decorative facia/frame assembly as detailed in section 8.3.

13. Check the purpose provided ventilation is un-obstructed.

14. Light the fire and test setting pressures.

15. Check safe operation of the appliance.

For specific servicing instructions, see relevant sections.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Smeg 50's Retro style Guide de dépannage Page 9

Commentaires sur ces manuels