Smeg Glass Ceramic Induction Hob SE2642ID2 Manuel d'utilisateur télécharger pdf (Page 14)

Instructions for assembly

Instructi ons for assembly

Safety instructions for kitchen unit fitters

• Veneers, adhesives and plastic surfaces of surrounding

furniture must be temperature resistant (>75°C). If the veneers

and surfaces are not sufficiently heat resistant they can

become deformed.

• Ensure that all live connections are safely insulated when

installing the hob.

• Cover strips between the wall and the worktop behind the hob

which are made of solid wood are permissible as long as

minimum clearances in accordance with the installation

diagrams are maintained.

• Minimum clearances of the hob cut-out towards the rear are to

be maintained in accordance with the installation diagram.

• For installation directly next to a tall cupboard, a safety

distance of at least 40 mm must be ensured. The side surface

of the tall cupboard should be fitted with heat resistant

material. Due to working requirements, however, the distance

should be at least 300 mm.

• The clearance between the hob and an extraction hood must

be at least as large as that stipulated in the assembly

instructions for the cooker hood.

• The packaging materials (plastic foil, polystyrene, nails etc.)

must be kept out of reach of children as these parts are

potentially dangerous. Small parts can be swallowed and there

is a danger of plastic sheeting causing suffocation.

Venilation

• Clearance between the induction hob and kitchen furniture or

built-in units must provide for sufficient ventilation of the induc-

tion hob.

• If the power level of a cooking zone is automatically raised or

lowered (see section on thermal cut-off device) it is likely that

the cooling system does not cool sufficiently.

In this case we recommend that the back wall of the bottom

kitchen unit in the area of the worktop cut-out be opened and

that the front transverse strip of the unit be removed over the

entire width of the appliance in order to promote the circulation

of air.

Installation

Important

• Remove any transverse strips underneath the worktop at least

in the area of the worktop cut-out.

• Avoid excessive thermal development from below e.g. from a

baking oven without a cross flow cooling device.

• The induction hob may not be used when pyrolysis operation

is taking place in a built-in oven.

• When installing the appliance on top of a drawer it is essential

to ensure that no sharp items are stored in the drawer since

these could become bent on the underside of the hob and

prevent the drawer from being opened and closed.

• If a shelf has been inserted underneath the hob, there must be

a clearance of at least 20 mm to the underside of the hob in

order to ensure that the hob is sufficiently ventilated.

• The hob may not be installed above refrigerators, freezers,

dishwashers, washing machines or dryers.

• To avoid danger of fire, make sure that no combustible objects

which could easily catch fire or become deformed on exposure

to heat are directly next to or under the surface.

Sealing of the hob

Before installation, correctly insert the sealing unit delivered with

the hob.

• No liquids may penetrate between the edge of the hob and the

worktop or between the hob and the wall and come into con-

tact with any electrical appliances.

• When installing a hob into an uneven worktop, e.g. with a

ceramic or similar covering (tiles etc.), the seal on the hob is to

be removed and the seal between the hob and worktop made

with plastic sealing materials (putty).

• The hob must under no circumstances be sealed with

silicone sealant!

This would make it impossible to remove the

hob at a later date without damaging it.

Working surface cut-out

Cut out the worktop recess accurately with a good, straight saw

blade or recessing machine. The cut edges should then be

sealed so that no moisture can penetrate.

The area is cut out as illustrated.

The glass ceramic hob must have a level and flush bearing. Any

distortion may lead to fracture of the glass panel.

Make sure that the sealing of the hob is properly seated.

The glass ceramic hob is fastened with clips or with brackets.

1 2 ... 9 10 11 12 13 14 15 16 17

Commentaires sur ces manuels

Pas de commentaire

Smeg Glass Ceramic Induction Hob SE2642ID2 Manuel d'utilisateur Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Plaques chauffantes Smeg Glass Ceramic Induction Hob SE2642ID2