Smeg P23LINP Guide de dépannage télécharger pdf (Page 5)

emove the outer packaging, remove any instructions or fixing kits. Read ALL these instructions before continuing to unpack or

install this appliance. Lift off the remaining packaging components and remove the contents of the box. Check that the compo-

nents supplied correlate with the component checklist. Please dispose of all the packaging materials at your local recycling centre.

All models: There are four possible entry points for the gas supply

pipework to enter the appliance firebox. The L23 firebox is shown in

figure 2 as an example, but the relative locations of these holes are the

same for all models.

These entry points are ‘knock out’ type holes. Non-concealed gas con-

nections may be made using the entry points in the bottom or sides of

the firebox. A concealed gas connection may be made using the knock

out hole in the centre back of the firebox. Select the most appropriate

entry point and knock out the relevant hole with a sharp tap from a ham-

mer and fit the rubber grommet supplied. A small incision can now be

made in the rubber to slip snugly around the outside of the supply pipe

and sleeving.

All installation pipework must be in accordance with the current edition

of National regulations/codes and the rules in force.

In order to avoid unnecessary pressure drops, use of small diameter pipe should be kept to a minimum, for example, we rec-

ommend no more than 1.5 metres of 8mm pipe. If a concealed gas connection is to be made, the supply pipe should always be

sleeved through walls and floors using the shortest possible route. For concealed supply pipe routing, pipes must (where possi-

ble) be vertical and providing there is sufficient wall thickness available, they should be placed in pipe chases. Horizontal pipe runs

should be avoided. Prior to chasing a solid wall, an inspection should be made to note the proximity of any cables/sockets out-

lets which may already be buried. Pipes must be secured using suitable clips and protected against corrosion. Ideally factory fin-

ished protected pipework and fittings should be used. Joints should be kept to a minimum and compression fittings must not be

used. The pipework installation must be tested for tightness before any protection is applied and/or the pipework and fittings are

buried.

Remove any protective film coatings from the finished/decorative surfaces of the appliance. After having selected the final mount-

ing position of the appliance, taking into account the requirements as specified in sections 3 and 4 of these instructions, the

integrity of the wall, and the feasibility of the proposed supply pipe routing, the firebox

of the appliance may be secured to the wall.

To ensure customer safety, be sure to design the installation so that the strength of

both the wall and any wall fixings used are sufficient.

Smeg S.p.A. assumes absolutely no responsibility for injuries and damages that may

occur due to improper installation or handling. The appliance should not be installed

until all wet plastering and/or dry wall sanding and wall painting has been completed.

Do not block the ventilation holes of the appliance. The wall onto which the appliance

is installed must be flat. Install only on a vertical surface. Avoid sloped surfaces.

Installation onto anything other than a vertical wall may result in fire, damage or injury.

If the appliance is to be mounted on the inner leaf of a conventional cavity brick wall, or a solid wall, then the wall plugs and fix-

ing screws provided may be used. Depending on the condition of the wall it may be necessary to use additional fixings. In this

situation, any additional fixings and wallplugs should be of the same size and type as the ones provided. At the appropriate stage

of the installation, drill four holes using only a 8mm masonry bit to a depth of 42mm. Insert the wallplugs provided ensuring they

are flush to the wall.

5.0 UNPACKING THE APPLIANCE

5.1 COMPONENT CHECKLIST

QUANTITY DESCRIPTION

1 Firebox and burner assembly

1 Set of manufacturers instructions

Decorative glass facia assembly (Linear and Classic models)

1 Painted decorative facia in one of several colours (Fab models)

1 Screw and wall plug pack

1 Rubber grommet

1 Fitting template

2008 Smeg S.p.A.

GB IE

6.0 GAS SUPPLY ROUTES

Figure 2

7.0 FIXING THE APPLIANCE

The wall where the appliance is

to be installed must be capable

of long-term support of the total

load of the appliance. Measures

should also be taken to ensure

sufficient strength to withstand

the force of earthquakes, vibra-

tion and other external forces.

WARNING

GB-IE-5

Smeg EU-wide instal instruc-v7-English.qxp:Smeg EU-wide installation instructions DRAFT A-12-12-07.qxd 17/7/08 12:07 Page 5

1 2 3 4 5 6 7 8 9 10 ... 14 15

Commentaires sur ces manuels

Pas de commentaire

Smeg P23LINP Guide de dépannage Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Foyers Smeg P23LINP